Toyota Tacoma Car Cover 2024-2026

Toyota Tacoma Car Cover 2024-2026

The fourth-generation Tacoma that arrived for 2024 is a different truck from the one it replaced. It is wider, the cab options changed, and the XtraCab replaced the old Access Cab with a different rear body section. A cover cut from 2016–2023 measurements will go on, then sit wrong: the hem rides up at the rocker panels and the rear section tents over the tailgate.

This page covers the 2024–2026 truck only. If you have an earlier Tacoma, use the 2016–2023 guide instead. Below is what the current truck measures, what to measure on your own vehicle, and the three fit points that catch new Tacoma owners.

2024–2026 Tacoma dimensions

ConfigurationOverall lengthOverall widthOverall heightFit note
XtraCab, 6 ft bed213.0 in76.9 in73.9–74.6 inTwo doors with a rear storage shelf instead of a back seat. The cab ends sooner than on the Double Cab, so the cover's cab section is shorter.
Double Cab, 5 ft bed213.0 in76.9–77.9 in73.9–74.6 inSame overall length as the XtraCab but a full rear door and glass area. Width varies with 4WD and trim.
Double Cab, 6 ft bed226.2 in77.9 in74.6 inLongest body in the range, about 13 in longer than the 5 ft version. A short-bed pattern will not reach the tailgate.

Published US-market dimensions. Two-wheel-drive trims typically sit about an inch lower and narrower than four-wheel-drive trims, and trucks with a lift, running boards or a bed rack measure outside these figures. Measure your own truck before ordering.

Three steps to the right cover

  1. Confirm cab and bed from the door jamb label. "Tacoma 2024" is not enough. XtraCab and Double Cab share one overall length on the 5 ft bed, so length alone cannot tell you which pattern you need.
  2. Measure four points with a tape. Bumper to bumper along the centreline, body width at the widest point excluding mirrors, ground to the highest point of the roof or rack, and the height of the roof antenna at the rear of the cab.
  3. Match the fabric to where the truck parks. A garage-kept truck needs a breathable dust cover; a truck that sits outside under trees needs a waterproof shell with taped seams and a soft lining, because grit trapped under a loose cover scratches paint faster than rain does.

Fit points that catch 2024+ Tacoma owners

The rear of the cab changed. On the XtraCab the rear body section is shorter and squarer than the old Access Cab, so a pattern drawn for the previous generation leaves slack behind the doors. Slack in that area lifts in crosswind and pulls the front hem off the bumper.

The bed is taller and the tailgate is heavier. The new tailgate has a damper and, on many trims, a built-in step. A cover cut flush to the old tailgate line will rub the top edge every time the gate closes. A correct pattern leaves clearance above the gate and closes below the bumper.

The roof antenna moved. On this generation it sits at the rear of the roof rather than on the front fender. A flat pattern presses it sideways; a pattern with a pocket lets the cover sit level.

Questions 2024+ Tacoma buyers ask

Will a cover for a 2016–2023 Tacoma fit my 2024?

No, not properly. The current truck is wider and the cab and bed proportions changed, so the older pattern will be tight across the body and short at the rear on the 6 ft bed. Order the pattern built for the 2024–2026 body.

Can I keep the cover on with a bed rack or tonneau fitted?

Yes, if the pattern is built around the accessory. A rack raises the highest point of the truck and a tonneau changes what the rear of the cover can wrap. Measure to the top of the rack, tell us the bed length, and the rear section is cut to clear it rather than to sit on the tailgate.

Next step

Match your cab and bed against the table, measure the four points above, and order a custom-fit Tacoma cover built to those numbers. Unsure which configuration you have? Send a side photo and a photo of the door jamb label through the contact page and we will confirm before the pattern is cut. For the previous generation, see the 2016–2023 Tacoma cover guide.

Other model cover guides

Same procedure, different body: these guides cover the dimensions and fit points for the models we cut most often.

Buying for a fleet or more than one vehicle? The full car cover range lists every pattern we cut, and the contact page is the fastest way to confirm a cab and bed combination.